x7722271404 / x772000164
99944200475
Power Edger Attachment
FOR MODELS: SRM-2400SB, 260SB, 261SB, PAS-2400, 2601, 230,
231, 260, 261, 265, 266, 280
Operator’s Manual
Users of this equipment risk injury to themselves and others if the unit is used
improperly and/or safety precautions are not followed. ECHO provides an operator’s
manual. It must be read and understood for proper and safe operation. Failure to do so
could result in serious injury.
Specifications, descriptions and illustrative material in this literature are as accurate as known at the time
of publication, but are subject to change without notice. Illustrations may include optional equipment and
accessories, and may not include all standard equipment.
X7702093705
© 4/2015 ECHO Inc.
99944200475
INTRODUCTION
INTRODUCTION
Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and
on-the-job dependability. Read and understand this manual and the SAFETY MANUAL. You will find both
easy to use and full of helpful operating tips and SAFETY messages.
The Operator’s Manual
Keep it in a safe place for future reference. Contains specifications and information for safety, operation,
maintenance, storage and assembly specific to this product.
The Safety Manual
Keep it in a safe place for future reference. Explains possible hazards and the measures you should take to
insure safe operation.
SERVICING INFORMATION
Parts/Serial Number
Genuine ECHO Parts and ECHO REPOWER™ Parts and
Assemblies for your ECHO products are available only from an
Authorized ECHO Dealer. When you do need to buy parts always
have the Model Number and Serial Number of the unit with you. You
can find these numbers on the engine housing. For future
reference, write them in the space provided below.
Model No. _________________ SN. ___________________
Service
Service of this product during the warranty period must be performed by an Authorized ECHO Service
Dealer. For the name and address of the Authorized ECHO Service Dealer nearest you, ask your retailer or
call: 1-800-432-ECHO (3246). Dealer information is also available on our Web Site. When presenting your
unit for Warranty service/repairs, proof of purchase is required.
Echo Consumer Product Support
If you require assistance or have questions concerning the application, operation or maintenance of this
product you may call the ECHO Consumer Product Support Department at 1-800-673-1558 from 8:00 am to
5:00 pm (Central Standard Time) Monday through Friday. Before calling, please know the model and serial
number of your unit.
Product Registration
To ensure trouble free warranty coverage it is important that you register your ECHO equipment on-line at
product confirms your warranty coverage and provides a direct link between you and ECHO if we find it
necessary to contact you.
X7702093705
3
© 4/2015 ECHO Inc.
SAFETY
99944200475
Additional or Replacement Manuals
For more information
scan this QR code.
Replacement Operator, Safety Manuals, and Parts Catalogs
or by contacting ECHO Inc., 400 Oakwood Road, Lake Zurich,
IL 60047 (800-673-1558). Always check the ECHO Web Site for
updated information.
Safety Videos are available from your Echo dealer. A $5.00 shipping charge will be required for each video.
SAFETY
Refer to your Pro Attachment Series or Split Boom Operator's Manual for correct engine fueling,
starting and stopping instructions.
Manual Safety Symbols and Important Information
Throughout this manual and on the product itself, you will find safety alerts and helpful, informational
messages preceded by symbols or key words. The following is an explanation of those symbols and key
words and what they mean to you.
The safety alert symbol accompanied by the word “DANGER” calls attention to an act or condition
which WILL lead to serious personal injury or death if not avoided.
The safety alert symbol accompanied by the word “WARNING” calls attention to an act or condition
which CAN lead to serious personal injury or death if not avoided.
The safety alert symbol accompanied by the word “CAUTION” calls attention to an act or condition
which may lead to minor or moderate personal injury if not avoided.
The enclosed message provides information necessary for the protection of the unit.
Note: This enclosed message provides tips for use, care and maintenance of the unit.
CIRCLE AND SLASH SYMBOL
This symbol means the specific action shown is prohibited. Ignoring these prohibitions can result
in serious or fatal injury.
4
X7702093705
© 4/2015 ECHO Inc.
99944200475
SAFETY
International Symbols
Symbol
Description
Symbol
Description
Symbol
Description
Symbol
Description
Warning, See
Operator’s
Manual
DO NOT USE
BLADES - Line
Head Only
Thrown
objects
Safety/Alert
Wear eye, ear
and head
protection
Plan retreat
pathfromfalling
objects
Finger Severing
Hot Surface
Wear hand
and foot
protection
A V O I D K I C K O U T .
Keep bystanders at least 15
meters (50 feet) away.
RotatingCutting
Attachment
Wear slip
resistant foot
wear
Wear Face
Shield
Beware Thrown Objects
Wear Eye Protection
Do not operate
closer than 15
M (50 ft.) from
electrical
Keep feet
away from
blade
Keep bystanders and helpers
away 15 m (50 ft.).
hazards.
Keep
bystanders at
le a s t 1 5 m e t e r s
(50 feet) away
Personal Condition and Safety Equipment
Users of this product risk injury to themselves and others if the unit is used improperly and/or safety
precautions are not followed. Proper clothing and safety gear must be worn when operating unit.
Physical Condition
Your judgment and physical dexterity may not be good:
• If you are tired or sick.
• If you are taking medication.
• If you have taken alcohol or drugs.
Operate unit only if you are physically and mentally well.
Eye Protection
• Eye protection that meets ANSI Z87.1 or CE requirements must be worn whenever you operate the
unit.
• For additional safety, a full-face shield may be worn over safety glasses or goggles to provide
protection from sharp branches or flying debris.
X7702093705
5
© 4/2015 ECHO Inc.
SAFETY
99944200475
Hand Protection
Wear sturdy, no-slip, rubber work gloves to improve your grip on the handles. Gloves also provide protection
against cuts and scratches, cold environments, and reduce the transmission of machine vibration to your
hands.
Hearing/Ear Protection
ECHO recommends wearing hearing protection whenever unit is used.
Breathing Protection
Operators who are sensitive to dust or other common airborne allergens may need to wear a dust mask to
prevent inhaling these materials while operating unit. Dust masks can provide protection against dust, plant
debris, and other plant matter such as pollen. Make sure the mask does not impair your vision, and replace
the mask as needed to prevent air restrictions.
Proper Clothing
Wear snug-fitting, durable clothing:
• Pants should have long legs, shirts should have long sleeves.
• DO NOT WEAR SHORTS.
• DO NOT WEAR TIES, SCARVES, JEWELRY, or clothing with loose or hanging items that could become
entangled in moving parts or surrounding growth.
• Keep clothing buttoned or zipped, and keep shirt tails tucked in.
Wear sturdy work shoes with nonskid rubber soles:
• DO NOT WEAR OPEN TOED SHOES.
• DO NOT OPERATE UNIT BAREFOOTED.
Keep long hair away from engine and air intake. Retain hair with cap or net.
Heavy protective clothing can increase operator fatigue, which may lead to heat stroke. Schedule heavy
work for early morning or late afternoon hours when temperatures are cooler.
The components of this machine generate an electromagnetic field during operation, which may
interfere with some pacemakers. To reduce the risk of serious or fatal injury, persons with
pacemakers should consult with their physician and the pacemaker manufacturer before operating
this machine. In the absence of such information, ECHO does not recommend the use of this
machine by anyone who has a pacemaker.
Extended Operation / Extreme Conditions
Prolonged exposure to cold and/or vibration may result in injury. Read and follow all safety and
operation instructions to minimize risk of injury. Failure to follow instructions may result in painful
wrist/hand/arm injuries.
6
X7702093705
© 4/2015 ECHO Inc.
99944200475
SAFETY
It is believed that a condition called Raynaud’s Phenomenon, which affects the fingers of certain individuals,
may be brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling
and burning sensations, followed by loss of color and numbness in the fingers. The following precautions are
strongly recommended, because the minimum exposure, which might trigger the ailment, is unknown.
• Keep your body warm, especially the head, neck, feet, ankles,
hands, and wrists.
• Maintain good blood circulation by performing vigorous arm
exercises during frequent work breaks, and also by not
smoking.
• Limit the hours of operation. Try to fill each day with jobs
where operating the unit or other hand-held power equipment
is not required.
• If you experience discomfort, redness, and swelling of the
fingers followed by whitening and loss of feeling, consult your physician before further exposing yourself to
cold and vibration.
Repetitive Stress Injuries (RSI)
It is believed that overusing the muscles and tendons of the fingers,
hands, arms, and shoulders may cause soreness, swelling,
numbness, weakness, and extreme pain in those areas. Certain
repetitive hand activities may put you at a high risk for developing a
Repetitive Stress Injury (RSI). An extreme RSI condition is Carpal
Tunnel Syndrome (CTS), which could occur when your wrist swells
and squeezes a vital nerve that runs through the area. Some believe
that prolonged exposure to vibration may contribute to CTS. CTS
can cause severe pain for months or even years.
To reduce the risk of RSI/CTS, do the following:
• Avoid using your wrist in a bent, extended, or twisted position.
Instead try to maintain a straight wrist position. Also, when
grasping, use your whole hand, not just the thumb and index finger.
• Take periodic breaks to minimize repetition and rest your hands.
• Reduce the speed and force with which you do the repetitive movement.
• Do exercise to strengthen the hand and arm muscles.
• Immediately stop using all power equipment and consult a doctor if you feel tingling, numbness, or pain in
the fingers, hands, wrists, or arms. The sooner RSI/CTS is diagnosed, the more likely permanent nerve
and muscle damage can be prevented.
All over head electrical conductors and communications wires can have electricity flow with high
voltages. This unit is not insulated against electrical current. Never touch wires directly or indirectly,
otherwise serious injury or death may result.
X7702093705
7
© 4/2015 ECHO Inc.
SAFETY
99944200475
Do not operate this product indoors or in inadequately ventilated areas. Engine exhaust contains
poisonous emissions and can cause serious injury or death.
Read the Manuals
• Provide all users of this equipment with the Operator’s Manual
and Safety Manual for instructions on Safe Operation.
Clear the Work Area
• Spectators and fellow workers must be warned, and children
and animals prevented from coming nearer than 15 m (50 ft.)
while the unit is in use.
Keep a Firm Grip
• Always hold throttle handle and support handle with thumbs
and fingers tightly encircling the handles.
Keep a Solid Stance
• Maintain footing and balance at all times. Do not stand on slippery, uneven or unstable surfaces. Do not
work in odd positions or on ladders. Do not over reach.
Avoid Hot Surfaces
• During operation, the drive shaft housing and attachment
bearing housing may become very hot, too hot to touch. Avoid
contact during and immediately after operation.
Equipment
Use this attachment with ECHO approved models only. Serious injury may result from the use of this
attachment combined with a non approved ECHO product.
• Check unit for loose/missing nuts, bolts, and screws. Tighten and/or replace as needed.
• Inspect shield for damage and that shield is securely in place. Replace if sjield is damaged or missing.
• Check that the cutting attachment is firmly attached and in safe operating condition.
Note: ECHO, INC. will not be responsible for the failure of cutting devices, attachments or accessories
which have not been tested and approved by ECHO.
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects
away from all openings.
◆ ALWAYS stop engine, disconnect spark plug, and make sure all moving parts have come to a complete
stop before removing obstructions, clearing debris, or servicing unit.
◆ DO NOT start or operate unit unless all guards and protective covers are properly assembled to unit.
8
X7702093705
© 4/2015 ECHO Inc.
99944200475
SAFETY
• NEVER reach into any opening while the engine is running. Moving parts may not be visible through
openings.
X7702093705
9
© 4/2015 ECHO Inc.
DESCRIPTION
99944200475
DESCRIPTION
Locate the safety decal(s) on your unit. Make sure the decal(s) is legible and that you understand and follow
the instructions on it. If a decal cannot be read, a new one can be ordered from your ECHO dealer. See
PARTS ORDERING instructions for specific information.
2
3
4
1
Shaft Label
1. BLADE - Rotates to provide cutting action.
2. DEBRIS SHIELD/FLAP - Mounted over the cutting attachment. Helps protect operator by deflecting
debris produced during the edging operation.
3. DRIVE SHAFT ASSEMBLY - Contains a specially designed liner and the flexible drive shaft.
4. WHEEL - Adjustable up/down, sets depth of blade.
10
X7702093705
© 4/2015 ECHO Inc.
99944200475
CONTENTS
CONTENTS
The ECHO product you purchased has been factory pre-assembled for your convenience.
After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or
missing parts. Use the contents list to check for missing parts.
____ - 1 - Power Edger Attachment
____ 1 - Operator’s Manual
X7722271404
/
X772000164
99944200475
Power Edger
Attachment
____ 1 - Warranty Registration Card
____ 2 - Split pin
Operator’s Manual
Burn Hazard
The muffler or catalytic muffler and surrounding cover may become extremely hot.
Always keep clear of exhaust and muffler area, otherwise serious personal injury may occur.
The engine exhaust from this product contains chemicals known to the State of California to causecancer.
birth defects or other reproductive harm.
____ 1 - Storage Hook Assembly
Read rules for safe operation and instructions carefully. ECHO provides an Operator’s Manual
and
a
Safety Manual. Both must be read and understood for proper and safe operation.
Specifications, descriptions and illustrative material in this literature are as accurate as known at the time
of publication, but are subject to change without notice. Illustrations may include optional equipment and
accessories, and may not include all standard equipment.
X7722271404 / X772000164
©
4/2011 ECHO Inc.
____
- Assembly Tool (s)
X7702093705
11
© 4/2015 ECHO Inc.
ASSEMBLY
99944200475
ASSEMBLY
Power Head Shaft/Lower Shaft Assembly
For more information
scan this QR code.
Do not perform maintenance or assembly procedures with
engine running.
Parts Required:
PAS or SRM-SB Power Head w/Shaft & Coupling
1. Set Power Head/Shaft Assembly on a level surface.
B
2. Pull locator pin (A) out, and turn counter-clockwise 1/4 turn
to lock-out position.
D
3. Remove vinyl cap from attachment drive shaft.
4. Remove cardboard spacer, if necessary.
E
C
5. Carefully fit attachment drive shaft assembly into coupler (B)
to decal assembly line (C), making sure that the inner lower
drive shaft engages the square upper drive shaft socket.
A
Note: Earlier model Power Heads may have shorter couplings.
Short couplings fit flush to decal point (E). New couplings
are 4-3/4 in. long, and fit flush to line (C).
Note: Lower bearing housing and head assembly must be in line with the engine.
6. Rotate locator pin (A) 1/4 turn clockwise to engage lower
D
shaft hole. Insure locator pin is fully engaged by twisting
lower drive shaft. Locator pin should snap flush in coupler.
Full engagement will prevent further shaft rotation.
C
7. Secure lower shaft assembly to coupler by tightening
clamping knob (D).
12
X7702093705
© 4/2015 ECHO Inc.
99944200475
OPERATION
OPERATION
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects
away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts
have come to a completestop before removing obstructions, clearing debris, or servicing unit. Allow
unit to cool before performing service.
Edger Operation Techniques
Engine exhaust IS HOT, and contains Carbon Monoxide (CO), a poison gas. Breathing CO can cause
unconsciousness, serious injury, or death. Exhaust can cause serious burns. ALWAYS position unit
so that exhaust is directed away from your face and body.
1. Before edging, water the area to soften the ground to make
edging easier.
2. Before edging, check the area and remove all obstacles and
objects that could be thrown.
3. Plan to edge regularly to make it easier to keep a neat edge
and to avoid having to make more than one pass.
Note: Blade depth may have to be adjusted due to differences
in height between the hard surface and the top of the
grass.
Never adjust blade height with engine running, otherwise serious personal injury may result.
4. Loosen adjustment knob and adjust the blade's depth of cut
to produce a fine cut between sidewalk and grass using a
minimum blade depth, usually with about 13 mm (1/2 in.) of
the blade into the ground. Tighten adjustment knob.
5. Before edging, plan your direction of travel so that the unit
will always be positioned on your right side and so that you
walk on a hard surface whenever possible.
6. Hold edger as shown.
Before edging, be sure to read and understand the entire
Operator's Manual to avoid serious injury.
X7702093705
13
© 4/2015 ECHO Inc.
OPERATION
99944200475
7. When starting to edge, run the engine at full throttle, and
lower the blade gently into the ground, being careful not to
hit the concrete with the blade.
8. Don't force the blade. Move only as quickly as the blade will
allow.
The complete unit, specifically the drive shaft assembly
and muffler exhaust area may become very hot during use.
Avoid contact during and immediately after operation,
otherwise serious personal injury may result.
14
X7702093705
© 4/2015 ECHO Inc.
99944200475
MAINTENANCE
MAINTENANCE
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects
away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts
have come to a complete stop before removing obstructions, clearing debris, or servicing unit.
Allow unit to cool before performing service. Wear gloves to protect hands from sharp edges and
hot surfaces.
Your ECHO unit is designed to provide many hours of trouble free service. Regular scheduled maintenance
will help your unit achieve that goal. If you are unsure or are not equipped with the necessary tools, you may
want to take your unit to an ECHO Service Dealer for maintenance. To help you decide whether you want to
DO-IT-YOURSELF or have the ECHO Dealer do it, each maintenance task has been graded. If the task is
not listed, see your ECHO Dealer for repairs.
Skill Levels
Level 1 = Easy to do. Common tools may be required.
Level 2 = Moderate difficulty. Some specialized tools may be required.
ECHO offers REPOWERTM Maintenance Kits and Parts to make your maintenance job easier.
Maintenance Intervals
Skill
Level
Component/System
Maintenance Procedure
Grease
Interval
Drive Shaft
1
1
1
Every 25 hours of use [1]
Every15 - 25 hours of use [1]
Before Each Use
Gear Housing
Grease
Screws/Nuts/Bolts
Inspect/Tighten/Replace
IMPORTANT - Time intervals shown are maximum. Actual use and your experience will determine the
frequency of required maintenance.
(1) Apply lithium based grease.
Blade Replacement/Lubrication
Level 1.
POWER BLENDXTM 8 oz. or Lithium Base
Grease, Blade, new split pin
Parts Required:
Gear Case
Note: Grease gear case every 15 - 25 hours of use. Replace
blade when it is worn shorter than 6 in. Remove blade and holders before greasing to prevent
damage to gear and bearings.
1. Shut engine off.
2. Remove split pin (A).
X7702093705
15
© 4/2015 ECHO Inc.
MAINTENANCE
99944200475
3. Rotate blade until holes in inner blade adapter (B) and gear
box align. Insert locking tool to lock PTO shaft (C).
Note: Blade nut (D) is left hand thread.
4. Remove blade nut (D) in a clockwise direction using
T-wrench. Remove outer blade adapter (E), blade (F) and
inner blade adapter (B).
5. Clean all loose debris from gear box.
6. Remove plug (G) and check level of grease. Grease should
fill gear case to bottom of grease plug hole.
B
C
F
E
D
A
7. Add grease if necessary using squeeze-type tube. Do not
use high pressure grease gun. DO NOT over-fill.
8. Install inner blade adapter (B) onto PTO shaft (C).
9. Install and center new blade (F) onto inner adapter (B).
G
10. Install outer adapter (E) and nut (D). Tighten nut (D) firmly,
counterclockwise (CCW).
Note: Never reuse old split pin.
11. Install new split pin (A) to secure nut.
16
X7702093705
© 4/2015 ECHO Inc.
99944200475
MAINTENANCE
Drive Shaft (Lower)
A
1. Loosen screws (A) and remove center locating screw (B).
Pull gear box and shield from drive shaft housing.
2. Pull flexible cable (C) from the drive shaft housing, wipe
clean and re-coat with a thin coating [15 ml (1/2 oz.)] of
grease.
3. Slide the flexible cable (C) back in the drive housing. DO
NOT get dirt on the flex cable.
B
4. Install the gear housing and shield assembly.
5. Tighten screws securely.
C
X7702093705
17
© 4/2015 ECHO Inc.
STORAGE
99944200475
STORAGE
Storage Hook Installation
1. Insert small end of hook into locating hole on attachment
shaft.
2. Slide plastic cap onto end of attachment shaft.
18
X7702093705
© 4/2015 ECHO Inc.
99944200475
SPECIFICATIONS
SPECIFICATIONS
MODEL
Shaft Length
99944200475
825 mm (32.48 in.)
150 mm (5.9 in.)
Attachment Width
Attachment Height
Weight w/blade
Drive Shaft Type
Rotating Direction
Blade Length
295 mm (11.61 in.)
2.49 kg (5.5 lb.)
6.35 mm (1/4 in.) Flex Shaft
Clockwise; viewed from right side
203 mm (8 in.)
Gear Case Ratio
Shield
2.07 : 1.0 Reduction
Open, anti-clog
X7702093705
19
© 4/2015 ECHO Inc.
WARRANTY STATEMENTS
99944200475
WARRANTY STATEMENTS
ECHO LIMITED WARRANTY STATEMENT FOR
PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010
ECHO'S RESPONSIBILITY
ECHO Incorporated’s Limited Warranty, provides to the original purchaser that this ECHO product is free from defects in material and workmanship.
Under normal use and maintenance from date of purchase, ECHO agrees to repair or replace at ECHO’s discretion, any defective product
free of charge at any authorized ECHO servicing dealer within listed below application time periods, limitations and exclusions. THIS LIMITED
WARRANTY IS ONLYAPPLICABLE TO ECHO PRODUCTS SOLD BYAUTHORIZED ECHO DEALERS. IT IS EXTENDED TO THE ORIGINAL
PURCHASER ONLY, AND IS NOT TRANSFERABLE TO SUBSEQUENT OWNERS EXCEPT FOR EMISSION RELATED PARTS. Repair
parts and accessories replaced under this warranty are warranted only for the balance of the original unit or accessory warranty period. Any
damage caused by improper installation or improper maintenance is not covered by this warranty. All parts or products replaced under warranty
become the property of ECHO, Inc. This warranty is separate from the Emission control warranty statement supplied with your new product.
Please consult the Emission Control Warranty Statement for details regarding emission related parts. For a list of Authorized ECHO Dealers
refer to WWW.ECHO-USA.COM or call 1-800-432-ECHO.
OWNER’S RESPONSIBILITY
To ensure trouble free warranty coverage it is important that you register your ECHO equipment on-line at WWW.ECHO-USA.COMꢀRUꢀE\ꢀ¿OO-
LQJꢀRXWꢀWKHꢀZDUUDQW\ꢀUHJLVWUDWLRQꢀFDUGꢀVXSSOLHGꢀZLWKꢀ\RXUꢀXQLWꢁꢀ5HJLVWHULQJꢀ\RXUꢀSURGXFWꢀFRQ¿UPVꢀ\RXUꢀZDUUDQW\ꢀFRYHUDJHꢀDQGꢀSURYLGHVꢀDꢀGLUHFWꢀ
OLQNꢀLIꢀZHꢀ¿QGꢀLWꢀQHFHVVDU\ꢀWRꢀFRQWDFWꢀ\RXꢁ
The owner shall demonstrate reasonable care and use, and follow preventative maintenance, storage, fuel and oil usage as prescribed in the
RSHUDWRU¶VꢀPDQXDOꢁꢀ6KRXOGꢀDꢀSURGXFWꢀGLI¿FXOW\ꢀRFFXUꢂꢀ\RXꢀPXVWꢂꢀDWꢀ\RXUꢀH[SHQVHꢂꢀGHOLYHUꢀRUꢀVKLSꢀ\RXUꢀ(&+2ꢀXQLWꢀWRꢀDQꢀDXWKRUL]HGꢀ(&+2ꢀVHUYLFLQJꢀ
dealer for warranty repairs (within the applicable warranty period), and arrange for pick-up or return of your unit after the repairs have been
made. For your nearest authorized ECHO servicing dealer, call ECHO’s Dealer Referral Center, at 1-800-432-ECHO or you can locate an ECHO
servicing dealer at WWW.ECHO-USA.COM. Should you require assistance or have questions concerning ECHO’s Warranty Statement, you
can contact our Consumer Product Support Department at 1-800-673-1558 or contact us through the web at WWW.ECHO-USA.COM.
PRODUCT WARRANTY PERIOD
HOMEOWNER APPLICATION
•
5 YEAR WARRANTY - All units for homeowner, or non-income producing use will be covered by this limited warranty for ¿YH ꢀꢁꢂꢃ\HDUV from
date of purchase.
EXCEPTIONS:
‡ꢀ )RUꢀWZRꢃVWURNHꢀHQJLQHꢀSRZHUHGꢀSURGXFWVꢂꢀWKHꢀHOHFWURQLFꢀLJQLWLRQꢀPRGXOHꢂꢀÀH[LEOHꢀGULYHꢀFDEOHVꢂꢀ650ꢀVROLGꢀGULYHꢀVKDIWVꢂꢀDQGꢀ7&ꢀWLQHVꢀ
are warranted for the OLIHꢄ of the product on parts only.
•
Cutting attachments such as, but not limited to, bars, chains, sprockets, blades, and nylon trimmer heads for homeowner or non-
income producing use will be covered for failures due to defects in material or workmanship for a period of ꢅꢆꢃGD\V from original
product purchase date. Any misuse from contact with concrete, rocks, or other structures is not covered by this warranty.
ECHO’s Rapid Loader String Head carries a lifetime warranty on the line locking system, parts only; no labor. Refer to your operator’s
manual for string head installation and maintenance instructions.
•
•
All SB-Series and PRO ATTACHMENT SERIES Split Shaft attachments carry the same warranty duration as the units they are
GHVLJQHGꢀWRꢀ¿Wꢁ
COMMERCIAL APPLICATION
•
1 YEAR WARRANTY - All Chain Saws, QuikVent Saws, and Cut-Off Saws for commercial, institutional, agricultural, industrial, or income
producing use will be covered by this limited warranty for one ꢀꢇꢂꢃ\HDU from the date of purchase.
2 YEAR WARRANTY - All other units for commercial, institutional, agricultural, industrial, or income producing use will be covered by this
limited warranty for two ꢀꢈꢂꢃ\HDUV from the date of purchase.
•
EXCEPTIONS:
‡ꢀ )RUꢀWZRꢃVWURNHꢀHQJLQHꢀSRZHUHGꢀSURGXFWVꢂꢀWKHꢀHOHFWURQLFꢀLJQLWLRQꢀPRGXOHꢂꢀÀH[LEOHꢀGULYHꢀFDEOHVꢂꢀ650ꢀVROLGꢀGULYHꢀVKDIWVꢀDQGꢀ7&ꢀWLQHVꢂꢀ
are warranted for the OLIHꢄ of the product on parts only.
•
Cutting attachments such as, but not limited to, bars, chains, sprockets, blades, and nylon trimmer heads for commercial, institutional,
agricultural, industrial, rental, or income producing will be covered for failures due to defects in material or workmanship for a period
of ꢉꢆꢃGD\V from original product purchase date. Any misuse from contact with concrete, rocks, or other structures is not covered by
this warranty.
•
•
ECHO’s Rapid Loader String Head carries a lifetime warranty on the line locking system, parts only; no labor. Refer to your operator’s
manual for string head installation and maintenance instructions.
All SB-Series and PRO ATTACHMENT SERIES Split Shaft attachments carry the same warranty duration as the units they are
GHVLJQHGꢀWRꢀ¿Wꢁ
RENTAL APPLICATION - 90 DAYS WARRANTY
• Units for rental use will be covered against defects in material and workmanship for a period of 90 days from the date of purchase.
ꢄꢀꢀ (&+2¶VꢀOLDELOLW\ꢀXQGHUꢀWKHꢀ³/LIHWLPH´ꢀFRYHUDJHꢀLVꢀOLPLWHGꢀWRꢀIXUQLVKLQJꢀSDUWVꢀVSHFL¿HGꢀXQGHUꢀWKHꢀPRODUCT WARRANTY PERIOD section of
this warranty statement for ³/LIH´ꢀIUHHꢀRIꢀFKDUJHꢀIRUꢀDꢀSHULRGꢀRIꢀWHQꢀꢄꢅꢆꢇꢀ\HDUVꢀDIWHUꢀWKHꢀGDWHꢀRIꢀWKHꢀFRPSOHWHꢀXQLW¶Vꢀ¿QDOꢀSURGXFWLRQꢁꢀ
20
X7702093705
© 4/2015 ECHO Inc.
99944200475
WARRANTY STATEMENTS
ECHO does not offer an over the counter exchange program. Any ECHO product re-built other than by ECHO or sold through an unauthorized
dealer, or an unauthorized outlet store, is sold without ECHO’s limited warranty coverage. The ECHO Limited Warranty coverage is extended
to the original purchaser only, and is not transferable except for emission related parts. Repair parts and accessories replaced under this
warranty are warranted only for the balance of the original unit or accessory warranty period. Any damage caused by improper installation or
improper maintenance is not covered by this warranty. All parts or products replaced under warranty become the property of ECHO.
PURCHASED REPAIR PARTS, SHORT BLOCKS AND ACCESSORIES
• 90-day homeowner, or non-income producing warranty
• 30-day commercial, institutional, agricultural, industrial, income producing, or rental application warranty
ATTENTION TWO-STROKE ENGINE POWER PRODUCT OWNERS
This ECHO two-stroke engine power product is a quality-engineered unit which has been manufactured to exact tolerances to provide superior
performance. To help ensure the performance of the unit, it is required to use two-stroke oil which meets the ISO-L-EGD Standard per ISO/CD
13738 and JASO M345FD Standards. (&+2ꢃ3RZHUꢃ%OHQGŒꢃ7ZRꢊ6WURNHꢃ2LO LVꢀDꢀSUHPLXPꢀWZRꢃVWURNHꢀRLOꢀVSHFL¿FDOO\ꢀIRUPXODWHGꢀWRꢀPHHWꢀ,62ꢃ
L-EGD (ISO/CD 13738) and JASO M345FD Standards. The use of two-stroke oils designed for other applications, such as for outboard motors
or lawnmowers can result in severe engine damage, and will void your two-stroke engine limited warranty.
THIS WARRANTY DOES NOT COVER DAMAGE CAUSED BY:
•
Lack of lubrication or engine failure, due to the use of two-stroke oils that do not meet the ISO-L-EGD (ISO/CD 13738) and JASO M345FD
Standards. Engine problems due to inadequate lubrication caused by failure to use an ISO-L-EGD compliant and JASO M345FD registered
oil, will void the two-stroke engine limited warranty. ECHO Power Blend™ Two-Stroke Oil meets the ISO-L-EGD and JASO M345FD
Standard. Emission related parts are covered for 5 years homeowner use or 2 years commercial use regardless of two-stroke oil used, per
the statement listed in the EPA or California Emission Defect Warranty Explanation.
Damage caused by use of gasohol, containing methanol (wood alcohol), or gasoline containing less than 89 octane. Only use gasoline which
contains 89 octane or higher. Gasohol which contains a PD[LPXP 10% ethanol (grain alcohol) or 15% MTBE (methyl/tertiary/butyl/ether)
is also approved. The prescribed mixing ratio of gasoline to oil is listed on the ECHO oil label and covered in your operator’s manual.
(QJLQHꢀGDPDJHꢀFDXVHGꢀE\ꢀXVHꢀRIꢀHWKHUꢀRUꢀDQ\ꢀVWDUWLQJꢀÀXLGVꢁꢀꢀ
'DPDJHꢀFDXVHGꢀE\ꢀWDPSHULQJꢀZLWKꢀHQJLQHꢀVSHHGꢀJRYHUQRUꢀRUꢀHPLVVLRQꢀFRPSRQHQWVꢂꢀRUꢀUXQQLQJꢀHQJLQHVꢀDERYHꢀVSHFL¿HGꢀDQGꢀUHFRPPHQGHGꢀ
engine speeds as listed in your operator’s manual.
•
‡ꢀ
‡ꢀ
‡ꢀ
•
‡ꢀ
2SHUDWLRQꢀRIꢀWKHꢀXQLWꢀZLWKꢀLPSURSHUO\ꢀPDLQWDLQHGꢈUHPRYHGꢀFXWWLQJꢀVKLHOGꢀRUꢀUHPRYHGꢈGDPDJHGꢀDLUꢀ¿OWHUꢁꢀꢀ
Damage caused by dirt, pressure or steam cleaning the unit, salt water, corrosion, rust, varnish, abrasives, and moisture.
'HIHFWVꢂꢀPDOIXQFWLRQVꢀRUꢀIDLOXUHVꢀUHVXOWLQJꢀIURPꢀDEXVHꢂꢀPLVXVHꢂꢀQHJOHFWꢂꢀPRGL¿FDWLRQVꢂꢀDOWHUDWLRQVꢂꢀQRUPDOꢀZHDUꢂꢀLPSURSHUꢀVHUYLFLQJꢂꢀRUꢀXVHꢀ
of unauthorized attachments.
•
•
Incorrect storage procedures, stale fuel, including failure to provide or perform required maintenance services as prescribed in the operator's
manual. Preventative maintenance as outlined in the operators manual is the customer’s responsibility.
Failures due to improper set-up, pre-delivery service or repair service by anyone other than authorized ECHO servicing dealer during the
warranty period.
Certain parts and other items are not warranted, including but not limited to: lubricants, starter cords, and engine tune-ups.
Use of spark plugs other than those meeting performance and durability requirements of the OEM spark plug listed in the Operator's
Manuals.
Overheating or carbon scoring failures due to restricted, clogged exhaust port or combustion chamber, including damage to spark arrester
screen.
•
•
•
‡ꢀ
•
$GMXVWPHQWVꢀDIWHUꢀWKHꢀ¿UVWꢀꢄꢉꢆꢇꢀWKLUW\ꢀGD\VꢀDQGꢀEH\RQGꢂꢀVXFKꢀDVꢀFDUEXUHWRUꢀDGMXVWPHQWꢀDQGꢀWKURWWOHꢀFDEOHꢀDGMXVWPHQWꢁꢀ
Damage to gears or gear cases caused by contaminated grease or oil, use of incorrect type or viscosity of lubricants, and/or failure to comply
with recommended grease or oil change intervals.
•
‡ꢀ
•
Damage caused by loading SHRED 'N' VAC® beyond recommended capacity.
'DPDJHꢀFDXVHGꢀE\ꢀSXPSꢀRUꢀVSUD\HUꢀUXQQLQJꢀGU\ꢂꢀSXPSLQJꢀRUꢀVSUD\LQJꢀFDXVWLFꢀRUꢀÀDPPDEOHꢀPDWHULDOVꢂꢀRUꢀODFNꢀRIꢀRUꢀEURNHQꢀVWUDLQHUVꢁꢀ
Additional damage to parts or components due to continued use after operational problem or failure occurs. Should operational problem or
failure occur, the product should not be used, but delivered as is to an authorized ECHO servicing dealer.
It is a dealer’s and/or customer’s responsibility to complete and return the warranty registration card supplied with your ECHO product or by visiting
WWW.ECHO-USA.COM. Your receipt of purchase including date, model and serial number must be maintained and presented to an authorized
ECHO servicing dealer for warranty service. Proof of purchase rests solely with the customer. Some states do not allow limitations on how long
an implied warranty lasts, so the above limitations may not apply to you. Some states do not allow the exclusion or limitation of incidental or
FRQVHTXHQWLDOꢀGDPDJHVꢂꢀVRꢀ\RXꢀPD\ꢀDOVRꢀKDYHꢀRWKHUꢀVSHFL¿FꢀOHJDOꢀULJKWVꢀZKLFKꢀYDU\ꢀIURPꢀVWDWHꢀWRꢀVWDWHꢁꢀ7KLVꢀOLPLWHGꢀZDUUDQW\ꢀLVꢀJLYHQꢀE\ꢀ(&+2ꢀ
Incorporated, 400 Oakwood Rd., Lake Zurich, IL 60047.
DISCLAIMER OF IMPLIED WARRANTIES
This limited warranty is in lieu of all other expressed or implied warranties, including any warranty of FITNESS FOR A PARTICULAR PURPOSE
OR USE and any implied warranty of MERCHANTABILITYꢀRWKHUZLVHꢀDSSOLFDEOHꢀWRꢀWKLVꢀSURGXFWꢁꢀ(&+2ꢀDQGꢀLWVꢀDI¿OLDWHGꢀFRPSDQLHVꢀVKDOOꢀQRWꢀEHꢀ
OLDEOHꢀIRUꢀDQ\ꢀVSHFLDOꢀLQFLGHQWDOꢀRUꢀFRQVHTXHQWLDOꢀGDPDJHꢂꢀLQFOXGLQJꢀORVWꢀSUR¿WVꢁꢀ7KHUHꢀDUHꢀQRꢀZDUUDQWLHVꢀH[WHQGHGꢀRWKHUꢀWKDQꢀDVꢀSURYLGHGꢀKHUHLQꢁꢀ
7KLVꢀOLPLWHGꢀZDUUDQW\ꢀPD\ꢀEHꢀPRGL¿HGꢀRQO\ꢀE\ꢀ(&+2ꢁ
99922201032
11/18/2011
X7702093705
21
© 4/2015 ECHO Inc.
NOTES
99944200475
NOTES
22
X7702093705
© 4/2015 ECHO Inc.
99944200475
PRODUCT REGISTRATION
PRODUCT REGISTRATION
Thank you for choosing ECHO Power Equipment
and EASY! NOTE: your information will never be sold or misused by ECHO, Inc. Registering your purchase enables us
to contact you in the unlikely event of a service update or product recall, and verifies your ownership for warranty
consideration.
If you do not have access to the Internet, you can complete the form below and mail to:
ECHO Inc., Product Registration, PO Box 1139, Lake Zurich IL 60047.
X7702093705
23
© 4/2015 ECHO Inc.
NOTES
99944200475
NOTES
24
X7702093705
© 4/2015 ECHO Inc.
99944200475
NOTES
X7702093705
25
© 4/2015 ECHO Inc.
NOTES
99944200475
26
X7702093705
© 4/2015 ECHO Inc.
99944200475
NOTES
X7702093705
27
© 4/2015 ECHO Inc.
S08500001001/S08500999999
ECHO, INCORPORATED
400 Oakwood Road
Lake Zurich, IL 60047
28
|